Choosing the right size and grade of aggregates impact the overall strength of concrete. The aggregates are taken out from the natural resources and classified into different grades. Grading of aggregates helps to identify the right aggregates for any construction works.
The aggregates are used as an important ingredient in the preparation of concrete. The fine aggregates are used in concrete as a filler material, and the coarse aggregates give the compressive strength to the concrete.
When we estimate the concrete quantity, the aggregates will occupy 70 to 75% of the volume.
The classification of aggregates depends on the grain size, density, shape, and geographical origin. So the properties of aggregates will differ based on the classification, and it may influence the mix of the concrete and strength.
The properties of aggregates that decides their nature have been listed below.
The specific gravity of aggregates is calculated by the ratio between the weight of aggregates to the weight of water which equals the aggregate weight.
The high specific gravity of aggregates contains good quality, and at the same time, low specific gravity aggregates are weak and permeable.
Normally the specific gravity value of aggregates lies between 2 to 3 which is used in construction works. The specific gravity value shows the quality and strength of the material.
The volume of aggregates will change when it is subjected to moisture called bulkage.
When the moisture content is present in the sand, it forms a thin film around each sand particle that makes the adjusted particles push a little away from them. This change makes the overall volume of the sand increase.
The bulking of sand is in the range between 20% to 30% and for the coarse aggregate is minimal. Bulk density is the ratio between the dry weight of the aggregates to the saturated weight of aggregates in kg/litre.
The bulk density of aggregates is dependent on the compaction and grading of aggregates in concrete.
The presence of space between the aggregate particles is called voids. The saturated aggregates volume will be changed due to the presence of voids.
The aggregates may contain different chemical particles that react with the cement and form cracks on the concrete surface. So the aggregates must be tested to ensure that such kinds of particles are not present in the aggregates.
The size of aggregates less than 4.75mm is called fine aggregate and beyond 4.75mm is called coarse aggregates.
The size and shape of the aggregates impact the strength and durability of the concrete. The workability of concrete might be affected when using large size aggregates.
The maximum size of aggregates must not be less than 20mm in Reinforced concrete.
Moreover, the incorrect size of aggregates such as flaky, rounded, angular, and irregular aggregates increase the voids and reduce the bondage of other ingredients in concrete. It may increase the material cost and indirectly reduce the strength of the concrete.
The surface texture represents whether the surface of the aggregates is smooth, polished, or rough. The rough surface texture is good for developing higher bondage between other ingredients of concrete which increases the strength of the concrete.
We can see some tiny holes on the surface of the aggregates called pores and such kinds of rocks called porous rocks. The pores happen on aggregates due to the air bubbles formed on the surface when the molten magma solidification.
High pore aggregates may easily disintegrate when applying load.
The coarse aggregate should not absorb water else; it may create cracks on the surface of the concrete after hardening.
The water absorption is calculated by the ratio between the dry weight of aggregate to the saturated weight of the aggregate. The water absorption will affect the water-cement ratio in concrete.
The fineness denotes the particle size of the aggregates. Cracks may form when more fineness aggregates are used in concrete.
A high fineness value indicated the aggregate is coarser and a low fineness value indicates the aggregate is finer. The sieve analysis test founds the fineness of the aggregate.
The surface area of fine aggregate is higher than the coarse aggregate. The identification of the surface area of the aggregate is another parameter to grade the aggregate. The specific surface area is nothing but the surface area per unit weight of the aggregate.
Deleterious particles affect the bondage of the concrete ingredients, thus resulting in reduced strength and durability of the concrete. The aggregates which may be used in concrete must be free from silt, clay, and other marine impurities.
Determination of the crushing value of an aggregate is helpful to find the compressive strength of the aggregate, whether it is suitable for the concrete work or not. One of the important properties of aggregates affects the overall strength of the structure.
The aggregate impact value test is used to find the resistance capacity of aggregate from sudden impact applied on the aggregate.
The aggregates should not expand due to the change of weather conditions else it may create cracks on concrete surfaces.
It is not just size and grade that affects the strength but also the properties of aggregates.
Happy Learning 🙂
Before starting any civil engineering work, regardless of branches, horizontal, vertical, and angular measurements of…
The data measurements gathered from surveying helps establish the plan and design of all civil…
Surveying is the art and science of civil engineering that determines the relative (comparable) position…
The formation of cracks on the concrete surface may lead to reduce the durability of…
Understanding the different levels of structure seems a bit of a daunting task. Don’t worry…
We knew that pipes are used to transport gas or liquid substance from one place…
View Comments
Dear Sir
I liked the each & every topics ,You have Explained very well in a apparent way ,Thank you very much Sir.
Your notes are simple and we'll explanable to a student
I really like it, because i understand it very well as am read it.
Nice summary
Would like to receive lectures
Nice information and a good summary you actually help me learn more from you thank you